
DXLink Multi-format Multimode Duplex Fiber Transmitter
Model: DXF-TX-MMD
Part #: FG1010-362
- Only One Cable – Send audio and video, while passing Ethernet signals and power over one twisted pair cable
- Multi-Format Analog Port and HDMI Port – Supports legacy analog signals - RGBHV, Component, S-Video, and Composite, and digital HDMI/HDCP, DisplayPort++ and DVI signals
- Send HDMI signals up to 100 meters – Extend the reach of the HDMI signals far beyond the capabilities of typical HDMI cabling
- Standard Twisted Pair Cable – Save time and effort in installation by leveraging cost effective twisted pair cable, see the Cabling for Success with DXLink white paper for more details
- Power over DXLink
The DXLink Multi-Format Fiber Transmitter sends analog and digital audio and video signals including HDMI with HDCP up to 300 meters over multimode fiber. Use the DXLink Fiber Transmitter in conjunction with the Enova DGX 8, 16, 32 or 64 to transmit clear, uncompressed video at the fastest data rate in the industry – 10 Gbps. The DXF-TX-MMD also sends and receives control commands from the Enova DGX Digital Media Switcher with integrated NetLinx providing a total control and distribution solution to all end points.
COMMON APPLICATIONS
The ideal entry-point for any source designed into an Enova DGX integrated system that requires the distance capabilities and inherent security of fiber – or both; including campus-wide distribution of sources that are shared between classrooms, secure military applications, casinos, arenas and museums. Directly connect video sources such as PCs using the HD-15 multi-format input connection or HDMI input and easily include audio on the same fiber cable by using the stereo or digital audio connection.
- Only One Cable – Send audio and video, while passing Ethernet signals and power over one twisted pair cable
- Multi-Format Analog Port and HDMI Port – Supports legacy analog signals - RGBHV, Component, S-Video, and Composite, and digital HDMI/HDCP, DisplayPort++ and DVI signals
- Send HDMI signals up to 100 meters – Extend the reach of the HDMI signals far beyond the capabilities of typical HDMI cabling
- Standard Twisted Pair Cable – Save time and effort in installation by leveraging cost effective twisted pair cable, see the Cabling for Success with DXLink white paper for more details
- Power over DXLink
- Enabled – Designed for use with Enova DGX or DVX systems with DXLink inputs, PS-POE-AT-TC (FG423-84) or PDXL-2 (FG1090-170) to provide remotely located Power over DXLink (requires firmware v1.2.40 or above)
- DXLink Direct Connection – When receiving Power over DXLink
- from the PS-POE-AT-TC or PDXL-2, DXLink Wallplates can be connected directly to a DXLink Receiver for a point-to-point solution
- Power Remotely - Power over DXLink
- is carried over twisted pair to simplify installation when used with the Enova DGX, Enova DVX, PS-POE-AT-TC or PDXL-2
- 3D Support - Pass through latest video formats including 3D and Deep Color
- Surround Sound Support - Pass through high definition surround sound including Dolby Digital, DTS and up to 8-channel L-PCM at 32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192kHz
- HDCP Compliant
- DEALER BENEFITS
- HDMI/HDCP With Simplicity of Analog - Hassle-free plug-and-play operation eliminates the need for time-consuming cumbersome work-around tools to deal with HDCP key constraints and resolution incompatibilities
- Installation Friendly - Standard two gang size and remote powering capabilities allows the wallplate to be installed in virtually any location
- CUSTOMER BENEFITS
- Interruption-Free Content - Exclusive InstaGate Pro® Technology allows audio and video to be switched quickly and easily to every connected display without the difficulties typically associated with HDCP
- Easily Connect Guest Devices - Provides a versatile solution for environments where sources are consistently changing
- Fiber Optic Connector Type - LC-LC
- Fiber Optic Signals Supported - Audio
- Fiber Optic Signals Supported - DVI
- Fiber Optic Signals Supported - HD Component Video
- Fiber Optic Signals Supported - HDMI
- Fiber Optic Signals Supported - RGBHV
- Fiber Optic Signals Supported - RS-232
- Fiber Optic Signals Supported - VGA
- ROHS Compliant - Yes
- Warranty - Yes
- Spec Sheet available - Yes
- AC Voltage (Maximum): 240 Volts
- AC Voltage (Minimum): 100 Volts
- Active Power: 20 Watt
- Current Draw: 0.80 Amps
- Depth: 5.20 in
- Height: 1 in
- Width: 8.75 in
- Product Weight: 1.10 lbs
- Shipping Weight: 2.20 lbs
- Certifications: CE, FCC, UL
- Regulatory Compliance: HDCP, WEEE
- Operating Distance (Multimode): 984.25 ft
- Operating Temperature (Maximum): 104 F
- Operating Temperature (Minimum): 32 F
- Signal to Noise Ratio: 93 dB
- Warranty (Length/Type): 3 Years Limited
- Power:
- Power Connector: 2.1 mm DC Power Jack
- POWER SUPPLY:
- External, Included: Each Multi-Format TX ships with a desktop power supply with power cord
- 2.5 A at 12 V, Max 13.5 V
- Environmental:
- Temperature (Storage): 22° F to 158° F (-30° C to 70° C)
- Humidity (Operating): 5% to 85% RH (non-condensing)
- Humidity (Storage): 0% to 90% RH (non-condensing)
- Heat Dissipation (On): 69 BTU/hr
- Ethernet:
- Ethernet Connection: (1) RJ-45, TCP/IP Port (ICS LAN 10/100)
- DXLINK FIBER:
- Fiber Connector: LC Duplex conforming to ANSI TIA/EAI 604-10 (FOCIS 10A)
- Fiber Cable Type: OM3 50/125µm
- Fiber Cable Length: 300m (984 ft)
- Transport Layer Throughput: 10.3125 Gbps
- Fiber Transceiver Type: 10G SFP+
- Optical Wavelength: 850 nm
- Optical Budget:
- 6.8 dB (typical) between DXLink Fiber Transceivers
- Optical Modulation Amplitude (OMA): -4.3 dBm (min)
- Optical Modulation Amplitude (OMA) Sensitivity: -11.1 dBm (typ)
- Optical Transceiver Mean: -1 dBm (average power)
- HDMI:
- Input Connector: (1) HDMI Type A Female
- Compatible Formats: HDMI, HDCP , DVI
- Signal Type Support:
- HDMI
- DVI-D (single link with HDMI cable adapter)
- DisplayPort ++ (Input Only, with HDMI or DVI cable adapter)
- Local Loopback Output Connector: (1) HDMI Type A Female Local Loopback Output, +5 V DDC Pin Output 55 mA, non-scaling, DVI-D, non-scaling (Single Link With Cable Adapter)
- Progressive Resolution Support:
- 480p up to 1920x1200 @ 60 Hz
- Including but not limited to those resolutions shown in the "Instruction Manual - DXLink Fiber Transmitters and Receivers"
- Interlaced Resolution Support:
- 480i, 576i, 1080i
- Including but not limited to those resolutions shown in the "Instruction Manual - DXLink Fiber Transmitters and Receivers"
- Interlace video supported into the Transmitter, progressive only supported out of the Receiver unless in non-scaling Bypass
- 3D Format Support:
- Yes, if Scaler on corresponding output board or DXLink Fiber RX is set to Bypass mode
- Frame Packing 1080p 24Hz
- Frame Packing 720p 50/60Hz
- Frame Packing 1080i 50/60Hz
- Top-Bottom 1080p 24Hz
- Top-Bottom 720p 50/60Hz
- Side-by-Side Half 1080i 50/60Hz
- Deep Color Support:
- 24-bit, 30-bit
- 30-bit supported when the HDMI Output Board scaler or DXLink RX scaler is in Bypass mode using CEA-861 formats and resolution is 1080p60 or less
- Color Space Support:
- RGB 4:4:4
- YCbCr 4:4:4 and 4:2:2
- Input signal support for YCbCr 4:4:4 and 4:2:2, output color-space is converted to RGB 4:4:4
- HDCP Support:
- Yes
- Supports AMX HDCP InstaGate Pro Technology When used with an Enova DGX Digital Media Switcher the key support is up to 16 sinks per output, independent of source device
- CEC Support: None
- DDC/EDID Support:
- When used with Enova DGX 8/16/32/64 Digital Media Switchers the HDMI and VGA EDID is passed from the Enova Switcher input to the TX and is user re-programmable, see the "Enova DGX Digital Media Switcher Instruction Manual" for supported EDID resolutions for each board type
- Propagation Delay (Typical): 4.8 us
- Input Voltage (Nominal): 1.0 Vpp Differential
- Input Re-clocking (CDR): Yes
- Input Equalization: Yes, Adaptive
- Video Data Rate (Max):
- 4.95 Gbps / 5.568 Gbps
- 5.568 Gbps supported when the HDMI Output Board scaler or DXLink RX scaler is in Bypass mode using CEA-861 formats and resolution is 1080p60 or less
- Video Pixel Clock (Max):
- 185.625 MHz
- 185.625 MHz supported when the HDMI Output Board scaler or DXLink RX scaler is in Bypass mode using CEA-861 formats and resolution is 1080p60 or less
- Audio Format Support:
- Dolby TrueHD, Dolby Digital, DTS-HD Master Audio, DTS, 2 CH through 8 CH L-PCM
- Dolby Digital and DTS support up to 48kHz, 5.1 channels
- Audio Resolution: 16 bit to 24 bit
- Audio Sample Rate: 32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192kHz
- Local Audio Support: Insertion
- Analog Video:
- Input Connector: (1) HD-15, breakout cable required for RGB formats
- Compatible Formats:
- RGBHV, RGBs, RGsB
- YPbPr (HDTV)
- Y/c (S-Video), C (Composite)
- Progressive Resolution Support:
- 480p up to 1920x1200 @ 60 Hz
- including but not limited to those resolutions shown in the "Instruction Manual – DXLink Fiber Transmitters and Receivers"
- Interlaced Resolution Support:
- 480i, 576i, 1080i
- Including but not limited to those resolutions shown in the "Instruction Manual – DXLink Fiber Transmitters and Receivers"
- if input is interlaced, all scaled outputs will deinterlace video to a progressive resolution format. If in scaler Bypass mode interlaced input will pass through
- Auto-Adjust Input: Supported
- RGB Input Signal Level Range: 1 Vpp nominal
- RGB Input Impedance: 75 ohms
- HV Sync Input Signal Level Range: 2 to 5 Vpp
- HV Sync Input Impedance: 2.5 pF Typ, 10 pF Max
- Digital Processing: 24 bit, 165 MHz
- Y/Pb/Pr Input Signal Level Range: 1.0 Vpp for Y, 700 mVpp for Pb Pr
- Y/Pb/Pr Input Impedance: 75 ohms
- Y/c (S-Video) Input Signal Level Range: 1.0 Vpp for Y, 1.0 Vpp for c
- Y/c (S-Video) Input Impedance: 75 ohms
- C (Composite) Input Signal Level Range: 1.0 Vpp
- C (Composite) Input Impedance: 75ohms
- S/PDIF DIGITAL AUDIO:
- Input Connector: (1) RCA Jack, video signal must be present to pass audio
- Input Signal Types: S/PDIF, video signal must be present to pass audio
- S/PDIF Audio Format Support
- Dolby Digital, DTS, 2 CH L-PCM
- Dolby Digital and DTS support up to 48kHz, 5.1 channels
- S/PDIF Resolution: 16 to 24 bit
- S/PDIF Sample Rate: 32 kHz, 44.1 kHz, 48 kHz, 96 kHz
- S/PDIF Input Signal Level Range: 200 mVpp to 600 mVpp terminated
- S/PDIF Input Impedance: 75ohms
- Analog to Digital Reference Level: +2.5 dBu = 0 dBfs
- ANALOG AUDIO:
- Input Connector: (1) 3.5mm mini-stereo jack, video must be present to pass audio
- Input Signal Types: Stereo analog, video must be present to pass audio
- Analog Input Level (Max): +2.5 dBu, unbalanced
- Analog Input Impedance: 10kohms
- Analog to Digital Conversion: 48 kHz Sample Rate, 24-bit
- Analog to Digital Reference Level: +2.5 dBu = 0 dBfs
- USB (HID) KEYBOARD & MOUSE:
- USB (HID):
- (1) USB Mini A/B Connector ("HOST")
- Connect a DXLink Fiber TX to a PC and emulate keyboard and mouse commands from a DXLink Fiber Receiver
- For a list of HID devices which have been tested and found to be working well with the latest firmware
- For a list of HID devices which have been tested and found to be working well with the latest firmware please view the document
- Controls:
- ID Pushbutton
- Toggle between DHCP and static IP addressing
- Places system in NetLinx Device ID assignment mode
- Reset the factory default settings
- Restore the factory firmware image
- Advanced Configuration Interface: (1) USB Mini-B Connector ("PROGRAM") Serial:
- (1) 3.5mm Pluggable Phoenix Terminal Block
- Bidirectional RS-232 Standard NetLinx Baudrate 1200-115k
- Parity support Odd/Even/None
- IR RX: (1) 3.5mm Mini-Stereo Jack Port for IR03 Receiver (Optional)
- IR TX: (1) 3.5mm Pluggable Phoenix Terminal Block Port for IR01 Emitter (Optional)
- Indicators:
- Power Indicator: (1) Green LED indicates whether or not the DXF-TX-MMD is powered on
- Digital Video Indicator: (1) Green LED indicates the presence of video signals through the module
- Audio Indicator: (1) Green LED indicates the presence of digital audio signals through the module
- Analog Video Indicator: (3) Green LEDs, 1 lights to indicate the presence of the type of analog video through the Multi-Format TX (composite, Y/c; Y/Pb/Pr or RGB; RGBHV or RGBS)
- IR TX Indicator: (1) Red LED lights during the transmission of IR data via the rear IR port
- IR RX Indicator: (1) Yellow LED lights during the receipt of IR data via the rear IR port
- RS-232 TX Indicator: (1) Red LED shows serial transmit (TX) data activity
- RS-232 RX Indicator: (1) Yellow LED shows serial receive (RX) data activity
- LINK/ACT: (1) Green LED lights when the Ethernet cable is connected and an active link is established. This LED also blinks when receiving Ethernet data packets
- Status: (1) Green LED lights when the Controller is programmed and communicating properly
- CEC Indicator: Not currently supported
- USB Indicator: (1) Yellow LED lights when host device is connected
- Front Connectors:
- Advanced Configuration Interface: (1) USB Mini-B Connector ("PROGRAM")
- Local Loopback Output Connector: (1) HDMI Type A Female, non-scaling
- Back Connectors:
- Video Input: (1) HD-15 (RGBHV, RGBs, RGsB, Y/Pb/Pr, Y/c / S-Video, composite (breakout cable is required for RGB formats)
- HDMI Input: (1) HDMI Type A Female
- Analog Stereo Input: (1) 3.5mm Mini-Stereo Jack
- S/PDIF Digital Audio Input: (1) RCA Jack
- ICS LAN/Ethernet Port: (1) RJ-45 Connector, TCP/IP Port (ICS LAN 10/100) Serial:
- (1) 3.5mm Pluggable Phoenix Terminal Block
- Bidirectional RS-232 Standard NetLinx Baudrate 1200-115k
- Parity support Odd/Even/None IR RX
- IR RX: (1) 3.5mm Mini-Stereo Jack Port for IR03 Receiver (Optional)
- IR TX: (1) 3.5mm Pluggable Phoenix Terminal Block Port for IR01 Emitter (Optional)
- USB (HID) Keyboard & Mouse:
- (1) USB Mini A/B Connector ("HOST")
- Connect a DXLink Fiber TX to a PC and emulate keyboard and mouse commands from a DXLink Fiber Receiver DXLink Fiber Output: (1) LC Duplex conforming to ANSI TIA/EAI 604-10 (FOCIS 10A)
- DXLink Fiber Output: (1) LC Duplex conforming to ANSI TIA/EAI 604-10 (FOCIS 10A)
- Local Power: TBA
- General:
- MTBF: 124,232 hours
- Noise Level: 0 dBA @ 1m (typ), 45.3 dBA @ 1m (max)
- Airflow: Convection (openings on top of case, typ), forced air (out of front plate, when fan is active)
- Mounting Options:
- Compatible V Style mounting options:
- AVB-VSTYLE-RMK-FILL-1U, V Style Module Rack Mounting Tray /w Fill Plates, 5 1/4" Depth (FG1010-721)
- AVB-VSTYLE-RMK-1U, V Style Module Rack Mounting Tray, 5 1/4" Depth (FG1010-720)
- AVB-VSTYLE-SURFACE-MNT, V Style Single Module Surface Mount Brackets (FG1010-722)
- AVB-VSTYLE-POLE-MNT, V Style Single Module Pole Mounting Kit (FG1010-723)
- Safety Certification:
- Class 1 Eye safe per requirements of IEC 60825-1 / CDRH
- Included Accessories:
- Ships with a desktop power supply with power cord
- Optional Accessories:
- AVB-VSTYLE-RMK-FILL-1U, V Style Module Rack Mounting Tray /w Fill Plates, 5 1/4" Depth (FG1010-721)
- AVB-VSTYLE-RMK-1U, V Style Module Rack Mounting Tray, 5 1/4" Depth (FG1010-720)
- AVB-VSTYLE-SURFACE-MNT, V Style Single Module Surface Mount Brackets (FG1010-722)
- AVB-VSTYLE-POLE-MNT, V Style Single Module Pole Mounting Kit (FG1010-723)
- CC-NIRC, NetLinx IR Emitter Cable (FG10-000-11)
- IR03, External IR Receiver Module (FG-IR03)
- CC-USB, USB Programming Cable (FG10-5965)
- Compatible AMX Products:
- Enova DGX 8/16/32/64 Digital Media Switchers with DGX-I-DXF-MMD, Enova DGX DXLink Mutimode Fiber Input Board, Duplex (FG1058-622) installed
Suggested Products

Gable
7440 Fort Smallwood Rd
Baltimore, MD 21226
USA
(410) 255-6400
www.gablecompany.com